Skip to site navigation

Leaf cuttings

Home  |  
Gardening > Advice  > Leaf cuttings
last updated Sep 16, 2009
Join the RHS

RHS membership

Get gardening advice all year round.

Join the RHS


Buy as a gift

Advertisement
Propagating Sansevieria by leaf cuttings. Credit: Tim Sandall/RHS The Garden.

Some plants can be propagated from a whole or a part of a leaf. It is an easy way to increase numbers of our favourite indoor plants.

Suitable for... Back to top

Plants such as Streptocarpus, Sansevieria, Eucomis, Sinningia (syn. Gloxinia), Begonia masoniana and B. rex hybrids can be propagated from part-leaf cuttings.

Taking whole leaf cuttings is a suitable method of propagation for plants such as Sinningia (syn. Gloxinia), Saintpaulia and Peperomia.

Succulents such as Kalanchoe, Echeveria, and Crassula (for example Crassula ovata – the jade plant) are very successful when propagated by leaf cuttings.

Tender sedums (e.g. S. rubrum, S. hintonii, S. morganianum) as well as hardy herbaceous species (e.g. S. spectabile) can also be propagated from leaf cuttings.

When to take leaf cuttings Back to top

Leaf cuttings are best taken early in the growing season from spring to early summer, though some can be propagated any time of year.

How to take leaf cuttings Back to top

Always select healthy, young, fully grown foliage. Avoid any damaged, diseased material or leaves affected by pests. Use pot or trays filled with free draining compost such as seed and cutting compost or mix equal quantities of multipurpose compost and sharp sand or perlite.

Part-leaf cuttings

Streptocarpus: Select a full-grown leaf and cut in half along the midrib, which should be discarded. Using a seed tray make a shallow trench and insert the leaf, cut side down and firm in.

Sansevieria, Eucomis: Cut leaves horizontally into 5cm (2in) pieces and insert lower edge down. Make sure to keep the cuttings facing the direction that it was growing on the plant, alternatively cut into shallow chevrons. Insert the cuttings vertically about 2cm (3/4in) deep.

 Begonia, Sinningia: Cut across the main veins on the underside. Pin the leaf, cut side down onto the compost. Alternatively, cut the leaf into squares 2.5cm (1in) across each with a main vein. Pin the squares to the surface of the compost.

Aftercare

  • Water and allow to drain. Place in a propagator or a clear plastic bag in a light place out of direct sunlight. Leaf cuttings from tropical plants must be kept in high humidity at about 20°C (68°F).
  • When plantlets form, remove covers and allow them to grow on until large enough to pot up individually.

Whole-leaf cuttings

Sinningia (syn. Gloxinia), Saintpaulia (African violet), Peperomia: Cut the leaves with the stalk intact from the parent plant. Using pots, insert with the base of each leaf just touching the surface and treat as for part-leaf cuttings.

Kalanchoe, Echeveria, Crassula: Leaf cuttings of succulents should be left a day or two to callus (the cut surface thickens) before potting. Insert into pots filled to three-quarters depth with two parts cactus compost to one part fine grit, topped off with fine grit. Do not cover. Place in warm position and good light. Keep the compost just slightly moist.

Problems Back to top

The cutting will be prone to rotting off if the compost is too wet. Water carefully and air the cuttings about twice a week and remove any decaying leaves promptly.

The development of the plantlets will slow at low temperatures. Keep the cuttings at about 20°C (68°F).

Poor growth can be caused by low light levels. Place in a well lit place but protect from direct sunshine.

Watch out for pests such as aphids, whitefly and mealybug.

Links

Grey mould
Aphids
Whitefly
Mealybug

Quick facts

Suitable for Mostly tender indoor plants and succulents
Timing Spring to early summer for the best results
Difficulty Easy to moderate

Advertisement